View AK5355VN_7723278.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

asahi kasei [ak5355] ms0113-e-01 2005/01 - 1 - features the ak5355 is a low voltage 16bit a/d converter for digital audio systems. the ak5355 also includes an input gain amplifier, making it suitable for microphone applications or low-input signal levels. the analog signal input of the ak5355 is single-ended, eliminating the need for external filters. the ak5355 is housed in a space-saving 16pin tssop or 20pin qfn package. features 1. resolution: 16bits 2. recording functions ? gain amplifier (0db / +15db) ? digital hpf for dc-offset cancellation (fc=3.4hz@fs=44.1khz) 3. adc characteristics ? single-ended input ? input level: 1.8vpp@va=3.0v (= 0.6 x va) ? s/(n+d): 85db ? dr, s/n: 91db 4. master clock: 256fs/384fs/512fs 5. audio data format: msb first, 2?s compliment ? 16bit msb justified or i 2 s 8. power supply ? va, vd: 2.1 3.6v (typ. 3.0v) 9. power supply current: 5ma 10. ta = -40 85 c 11. package: 16pin tssop 20pin qfn (4.2mm x 4.2mm, 0.5mm pitch) lin vcom va vss mclk sdto bclk lrck vd a dc hpf a udio i/f controller clock divider pdn rin dif sel low power 16bit ? adc ak5355
asahi kasei [ak5355] ms0113-e-01 2005/01 - 2 - ? ordering guide ak5355vt -40 +85 c 16pin tssop (0.65mm pitch) AK5355VN -40 +85 c 20pin qfn (0.5mm pitch) akd5355 evaluation board for ak5355vt ? pin layout (ak5355vt) 1 vcom rin vss lin va vd sel nc top view 2 3 4 5 6 7 8 tst1 nc bclk mclk lrck sdto 16 15 14 13 12 11 10 9 dif pdn ? pin layout (AK5355VN) nc tst1 nc nc vcom dif pdn bclk mclk lrck rin lin vss va vd sdto nc nc nc sel top view 16 17 18 19 20 15 14 13 1 10 9 8 7 6 2 3 4 5 12 11 a k5355
asahi kasei [ak5355] ms0113-e-01 2005/01 - 3 - pin/function (ak5355vt) no. pin name i/o function 1 vcom o adc common voltage output pin 2 rin i rch input pin 3 lin i lch input pin 4 vss - ground pin 5 va - analog power supply pin, +3.0v 6 vd - digital power supply pin, +3.0v 7 sel i input gain select pin ?l?: 0db, ?h?: +15db 8 nc - nc pin (no internal bonding) 9 sdto o audio serial data output pin 10 lrck i input/output channel clock pin 11 mclk i master clock input pin 12 bclk i audio serial data clock pin 13 pdn i reset & power down pin ?l? : reset & power down, ?h? : normal operation 14 dif i audio data format select pin ?l?: msb justified, ?h?: i 2 s 15 nc - nc pin (no internal bonding) 16 tst1 i test pin (pull-down pin) this pin should be left floating or connected to vss note: all digital input pins should not be left floating.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 4 - pin/function (AK5355VN) no. pin name i/o function 1 rin i rch input pin 2 lin i lch input pin 3 vss - ground pin 4 va - analog power supply pin, +3.0v 5 vd - digital power supply pin, +3.0v 6 sel i input gain select pin ?l?: 0db, ?h?: +15db 7 nc - nc pin (no internal bonding) this pin should be left floating. 8 nc - nc pin (no internal bonding) this pin should be left floating. 9 nc - nc pin (no internal bonding) this pin should be left floating. 10 sdto o audio serial data output pin 11 lrck i input/output channel clock pin 12 mclk i master clock input pin 13 bclk i audio serial data clock pin 14 pdn i reset & power down pin ?l?: reset & power down, ?h?: normal operation 15 dif i audio data format select pin ?l?: msb justified, ?h?: i 2 s 16 nc - nc pin (no internal bonding) this pin should be left floating. 17 tst1 i test pin (pull-down pin) this pin should be left floating or connected to vss 18 nc - nc pin (no internal bonding) this pin should be left floating. 19 nc - nc pin (no internal bonding) this pin should be left floating. 20 vcom o adc common voltage output pin note: all digital input pins should not be left floating.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 5 - absolute maximum ratings (vss=0v; note 1) parameter symbol min max units power supply analog digital va vd -0.3 -0.3 4.6 4.6 v v input current (any pin except supplies) iin - 10 ma analog input voltage (lin, rin pins) vina -0.3 va+0.3 v digital input voltage vind -0.3 vd+0.3 v ambient temperature (power applied) ta -40 85 c storage temperature tstg -65 150 c note 1. all voltages with respect to ground. warning: operation at or beyond these limits may results in permanent damage to the device. normal operation is not guaranteed at these extremes. recommended operating conditions (vss=0v; note 1) parameter symbol min typ max units power supply analog (va pin) digital (vd pin) va vd 2.1 2.1 3.0 3.0 3.6 va v v note 1. all voltages with respect to ground. warning: akm assumes no responsibility for the usag e beyond the conditions in this data sheet.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 6 - analog characteristics (ta=25 c; va, vd=3.0v; fs=44.1khz; signal frequency=1khz; measurement frequency=10hz 20khz; unless otherwise specified) parameter min typ max units resolution 16 bits input pga characteristics (ipga): gain = 0db 1.65 1.8 1.95 vpp input voltage (note 2) gain = +15db 0.29 0.32 0.35 vpp gain = 0db 27 40 k ? input impedance gain = +15db 20 30 k ? adc analog input characteristics: (note 3) gain = 0db 75 85 db s/(n+d) (-0.5dbfs output) gain = +15db 70 80 db gain = 0db 84 91 db d-range (-60dbfs output, a-weight) gain = +15db 76 84 db gain = 0db 84 91 db s/n (a-weight) gain = +15db 76 84 db gain = 0db 90 100 db interchannel isolation gain = +15db 80 90 db gain = 0db 0.2 0.5 db interchannel gain mismatch gain = +15db 0.2 1.0 db power supplies power supply current: va+vd normal operation (pdn=?h?) 5 7.5 ma ak5355vt 10 100 a power down (pdn=?l?) (note 4) AK5355VN 10 20 a note 2. analog input voltage (full-scale voltage) scales with va. gain = 0db; 0.6 x va gain = +15db; 0.107 x va note 3. adc measurements are input from lin/ rin and routed through input gain amplifier. the internal hpf cancels the offset of input gain amplifier and adc. note 4. in case of power-down mode, all digital input pins including clocks pins (mclk, bclk and lrck) are held at vd or vss. pdn pin is held at vss.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 7 - filter characteristics (ta=25 c; va, vd=2.1 3.6v; fs=44.1khz) parameter symbol min typ max units adc digital filter (decimation lpf): passband (note 5) 0.1db -1.0db -3.0db pb 0 20.0 21.1 17.4 khz khz khz stopband (note 5) sb 27.0 khz passband ripple pr 0.1 db stopband attenuation sa 65 db group delay (note 6) gd 17.0 1/fs group delay distortion ? gd 0 s adc digital filter (hpf): frequency response (note 5) -3db -0.5db -0.1db fr 3.4 10 22 hz hz hz note 5. the passband and stopband frequencies scale with fs (sampling frequency). for examples, pb=0.454 x fs(@adc: -1.0db). note 6. the calculated delay time caused by digital filtering. this time is from the input of an analog signal to setting the 16bit data of both channels to the output register of the adc and includes the group delay of the hpf. dc characteristics (ta=25 c; va, vd=2.1 3.6v) parameter symbol min typ max units high-level input voltage (except for tst1 pin) low-level input voltage (except for tst1 pin) vih vil 75 % vd - - - - 25 % vd v v high-level output voltage (iout=-80 a) low-level output voltage (iout=80 a) voh vol vd-0.4 - - - 0.4 v v input leakage current (note 7) iin - - 10 a note 7. tst1 pin is pulled-down internally (typ. 100k ? )
asahi kasei [ak5355] ms0113-e-01 2005/01 - 8 - switching characteristics (ta=25 c; va, vd=2.1 3.6v; c l =20pf) parameter symbol min typ max units control clock frequency master clock (mclk) 256fs: frequency pulse width low pulse width high 384fs: frequency pulse width low pulse width high 512fs: frequency pulse width low pulse width high channel clock (lrck) frequency duty cycle fclk tclkl tclkh fclk tclkl tclkh fclk tclkl tclkh fs duty 2.048 28 28 3.072 23 23 4.096 16 16 8 45 11.2896 16.9344 22.5792 44.1 12.8 19.2 25.6 50 55 mhz ns ns mhz ns ns mhz ns ns khz % audio interface timing bclk period bclk pulse width low pulse width high bclk ? ? to lrck lrck edge to sdto (msb) bclk ? ? to sdto tblk tblkl tblkh tblr tdlr tdss 312.5 130 130 -tblkh+50 tblkl-50 80 80 ns ns ns ns ns ns reset / initializing timing pdn pulse width pdn ? ? to sdto (note 8) tpw tpwv 150 4128 ns 1/fs note 8. this is the number of lrck rising after the pdn pin is pulled high.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 9 - ? timing diagram mclk 1/fclk tclkh tclkl vih vil lrck 1/fs vih vil bclk tblk vih vil tblkh tblkl figure 1. clock timing vih lrck vil vih bclk tblr vil tdlr tdss sdto 50%vd d15 (msb) figure 2. audio data input/output timing (audio i/f = no.0) pdn sdto vil tpwv tpw 50%vd figure 3. reset timing
asahi kasei [ak5355] ms0113-e-01 2005/01 - 10 - operation overview ? system clock the clocks required to operate are mclk ( 256fs/384fs/512fs), lrck (fs) and bclk (32fs ). the master clock (mclk) should be synchronized with lrck. the phase between these clocks does not matter. the frequency of mclk can be input as 256fs, 384fs or 512fs. when the 384fs or 512fs is input , the internal master clock is divided into 2/3 or 1/2 automatically. *fs is sampling frequency. all external clocks (mclk, bclk and lrck) should always be present whenever the adc is in operation. if these clocks are not provided, the ak5355 may draw excess curren t and will not operate properly because it utilizes these clocks for internal dynamic refresh of registers. if the ex ternal clocks are not present, the ak5355 should be placed in power-down mode. ? audio data i/f format the sdto, bclk and lrck pins are connected to an external controller. the audio data format has two modes, msb-first and 2?s compliment. the data format is set using the dif pin. no. dif pin sdto (adc) lrck bclk figure 0 l 16bit msb justified lch: ?h?, rch: ?l? 32fs figure 4 1 h i 2 s compatible lch: ?l?, rch: ?h? 32fs figure 5 table 1. audio data format lrck bclk ( 32fs ) sdto(o) 012 8910 1213 15012 8910 1213 150 15 1 14 4 876 0 32 11 14 1 5 15 14 4 876 0 321 5 14 11 15 13 bclk ( 64fs ) sdto ( o ) 0 1 2 3 14 15 17 18 31 0 1 2 14 15 17 18 31 0 15 1 14 0 15 14 1 2 1 15 15:msb, 0:lsb lch data rch data 21 13 16 0 16 3 13 3 13 13 3 figure 4. audio data timing (no.0) lrck bclk ( 32fs ) sdto(o) 0 1 2 4 9 10 12 13 15 0 1 2 4 9 10 12 13 15 0 0 1 15 5 13 7 7 1 43 11 14 2 6 0 15 5 13 7 7 1 432 6 14 11 0 13 bclk(64fs) sdto ( o ) 0 1 2 3 14 15 17 18 31 0 1 2 4 14 15 17 18 31 0 1 15 0 15 13 2 1 15:msb, 0:lsb lch data rch data 21 14 16 0 16 3 14 14 3 2 14 3 4 figure 5. audio data timing (no. 1)
asahi kasei [ak5355] ms0113-e-01 2005/01 - 11 - ? digital high pass filter the ak5355 has a digital high pass filter (hpf) to cancel dc-offset in both the adc and input gain amplifier. the cut-off frequency of the hpf is 3.4hz at fs=44.1khz. this cut-off frequency scal es with the sampling frequency (fs). ? input gain amplifier the ak5355 includes an input gain amplifier. the gain can be changed to 0db or +15db by using the sel pin. input impedance is 40k ? typically. sel pin gain l 0db h +15db table 2. input gain amplifier ? power down the ak5355 is placed in the power-down mode by bringing pdn ?l?. the digital filter is also reset at the same time. this reset should always be done after power-up. an analog initialization cycle starts after exiting the power-down mode. the output data sdto becomes available after 4128 cycles of lrck clock. during initialization, the adc digital data outputs of both channels are forced to a 2?s complement ?0?. the adc outputs settle to the data corresponding to the input signals at the end of initialization (settling time equals the group delay time approximately). normal operation internal state pdn power-down initialize normal operation 4128/fs(93.6ms@fs=44.1khz) idle noise gd gd ?0?data a /d in (analog) a /d out (digital) clock in mclk,lrck,bclk (1) (2) (3) ?0?data idle noise notes: (1) digital output corresponding to the analog input is delayed by the group delay amount (gd). (2) a/d output is ?0? data in the power-down state. (3) when the external clocks (mclk, bclk and lrck) are stopped, the ak5355 should be placed in the power-down state. figure 6. power-down/up sequence example ? system reset the ak5355 should be reset once by bringing pdn ?l? upon power-up. the ak5355 is powered up and the internal timing starts clocking by lrck ? ? after exiting reset and power down state by mclk. the ak5355 is in the power-down mode until mclk and lrck are input.
asahi kasei [ak5355] ms0113-e-01 2005/01 - 12 - system design (ak5355vt) figure 7 shows the system connection diagram. an evaluation board [akd5355] is available which demonstrates the application circuit, optimum layout, power supply arrangements and measurement results. vcom 1 rin 2 lin 3 vss 4 va 5 vd 6 sel 7 nc 8 16 15 14 13 12 11 10 9 tst1 nc pdn bclk mclk lrck sdto top view 0.1 + + rch in lch in analog supply 10 + controller system ground analog ground dif reset + 0.1 2.2 mode setting 2.1 3.6v 0.1 10 + digital supply 2.1 3.6v figure 7. system connection diagram example (ak5355vt)
asahi kasei [ak5355] ms0113-e-01 2005/01 - 13 - system design (AK5355VN) figure 8 shows the system connection diagram. an evaluation board [akd5355] is available which demonstrates the application circuit, optimum layout, power supply arrangements and measurement results. 0.1 + + rch in lch in analog supply 10 + controller system grou n analog ground reset + 0.1 2.2 mode setting 2.1 3.6v 0.1 10 + digital supply 2.1 3.6v rin lin vss va vd vcom nc nc tst1 nc dif pdn bclk mclk lrck sel nc nc nc sdto top view 1 2 3 4 5 15 14 13 12 11 20 19 18 17 16 6 7 8 9 10 figure 8. system connection diagram example (AK5355VN)
asahi kasei [ak5355] ms0113-e-01 2005/01 - 14 - ? mic device connection example figure 9 and figure 10 show the connection example of mic device. in this case, a mono microphone is connected to lin pin the ak5355. unused rin pin can be open. th e power supply for the microphone is provided via 4.4k ? (2.2k ? + 2.2k ? ) from analog power supply. the power supply noise prov ided to the microphone should be care because the microphone gain is usually high, around 40db. in figure 9, 1 st order lpf by 2.2k ? and 10 f is inserted between the power supply and the microphone. the ak5355 has a gain of +15db in analog stage. however, as the usual application needs a gain of around 40db or 50db, the shortage of gain, 25db or 35db, should be covered by digital processing like dsp. the total s/n in each gain level is shown in table 3 analog gain digital gain s/n +15db 0db 83db +15db +25db 58db +15db +35db 48db table 3. s/n of each gain level vcom 1 rin 2 lin 3 vss 4 va 5 vd 6 sel 7 nc 8 16 15 14 13 12 11 10 9 tst1 nc pdn bclk mclk lrck sdto top view 0.1 analog supply 10 + controller system ground analog ground dif reset + 0.1 2.2 mode setting 2.1 3.6v 0.1 10 + digital supply 2.1 3.6v mic 10 + 2.2k 2.2k 0.1 figure 9. mic device connection example (ak5355vt)
asahi kasei [ak5355] ms0113-e-01 2005/01 - 15 - 0.1 analog supply 10 + controller system grou n analog ground reset + 0.1 2.2 mode setting 2.1 3.6v 0.1 10 + digital supply 2.1 3.6v rin lin vss va vd vcom nc nc tst1 nc dif pdn bclk mclk lrck sel nc nc nc sdto top view 1 2 3 4 5 15 14 13 12 11 20 19 18 17 16 6 7 8 9 10 mic 10 + 2.2k 2.2k 0.1 figure 10. mic device connection example (AK5355VN)
asahi kasei [ak5355] ms0113-e-01 2005/01 - 16 - 1. grounding and power supply decoupling the ak5355 requires careful attention to power supply and grounding arrangements. va is usually supplied from the analog supply in the system. vd is a power supply pin to interface with the external ics and is supplied from the digital supply in the system. vss of the ak5355 should be connected to the analog ground plane. system analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. decoupling capacitors should be as near to the ak5355 as possible, with the small value ceramic capacitor being the nearest. 2. voltage reference the input to va voltage sets the analog input range. a 0.1 f ceramic capacitor and a 10 f electrolytic capacitor are normally connected to va and vss pins. vcom is a signal ground of this chip. an electrolytic 2.2 f in parallel with a 0.1 f ceramic capacitor attached to these pins eliminates the effects of high frequency noise. no load current may be drawn from the vcom pin. all signals, especially clock, shoul d be kept away from the va, vd and vcom pins in order to avoid unwanted coupling into the ak5355. 3. analog inputs the analog inputs are single-ended and the input resistance is 40k ? (typ). the input signal range scales with nominally (0.6 x va) vpp (typ) @ gain = 0db centered around the internal common voltage (typ. 0.45 x va). usually, the input signal cuts dc with a capacitor. the cut-off frequency is fc=(1/2 rc). the adc output data format is 2?s complement. the dc offset including the adc?s own dc offset is removed by the internal hpf (fc=3.4hz@fs=44.1khz).
asahi kasei [ak5355] ms0113-e-01 2005/01 - 17 - package (ak5355vt) 0-10 detail a seating plane 0.10 0.17 0.1 0.65 *5.0 0.1 1.05 0.05 a 1 8 9 16 16 p in tssop ( unit: mm ) *4.4 0.1 6.4 0.2 0.5 0.2 0.1 0.1 note: dimension "*" does not include mold flash. 0.13 m ? package & lead frame material package molding compound: epoxy lead frame material: cu lead frame surface treatment: solder (pb free) plate
asahi kasei [ak5355] ms0113-e-01 2005/01 - 18 - package (AK5355VN) 20pin qfn (unit: mm) 4.20 0.10 4.20 0.10 0.22 0.05 4.00 0.05 4.00 0.05 0.50 0.05 m 0.05 1.00 sab 1.00 c0.7 0.22 0.05 45.0 45.0 3 - 0 . 6 9 0 . 1 1 0 . 3 5 0 . 1 1 0.50 b a 3 - c0.2 0.60 0.10 s + 0.03 - 0.05 0.22 s 0.02typ 0.005min 0.04max 0.90 0.05 note: the black parts of back package should be open. ? package & lead frame material package molding compound: epoxy lead frame material: cu lead frame surface treatment: solder (pb free) plate
asahi kasei [ak5355] ms0113-e-01 2005/01 - 19 - marking (ak5355vt) akm 5355vt xxyyy 1) pin #1 indication 2) date code : xxyyy (5 digits) xx : lot# yyy : date code 3) marketing code : 5355vt 4) asahi kasei logo
asahi kasei [ak5355] ms0113-e-01 2005/01 - 20 - marking (ak5355vt) 5355 x xxx 1 xxxx : date code identifier (4 digits) revision history date (yy/mm/dd) revision reason page contents 01/08/27 00 first edition 05/01/20 01 spec addition 2 20pin qfn package is added. 6 power supply current (power-down mode, 20qfn): 20 a(max) important notice ? these products and their specifications are subject to change without notice. before considering any use or application, consult the asahi kasei microsystems co., ltd. (akm) sales office or authorized distributor concerning their current status. ? akm assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. ? any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. ? akm products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and akm assumes no responsibility relating to any such use, except with the express written consent of the representative director of akm. as used here: a. a hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. b. a critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. ? it is the responsibility of the buyer or distributor of an akm product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold akm harmless from any and all claims arising from the use of said product in the absence of such notification.

▲Up To Search▲

Price & Availability of AK5355VN

	To Download AK5355VN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .